
Sarah (my wife) & I have a houseboat on a lake about an hour from our
home. There are many birds there including Buzzards,
Bald Eagle & Heron. This must be where the Heron became my
favorite bird. So after deciding to sculpt one in an upcoming
competition, I started gathering photos. |

When gathering photos my objective is to capture just 1 aspect of the
animal I am going to create. These first 2 photos show very nice
photos of a herons body, neck & head. |

These 2 photos show the wings silhouette and details |

Finally, this one shows their long skinny legs |

Using all of the above reference, I made this drawing |

Figuring out where you are going to get the ice from & how to stack it
is called the "Block Layout"
Spend a lot of time on your block layout, make your design as
large as possible while still maintaining proportions. I kept
reducing the size of my bird until all of the parts just fit in the
block. Notice that the delicate pieces have spares. Can you
see where to get an extra wing tip from? Can you see where to get
ice for 2 spare legs? |

Wings have action, so I did this drawing to figure out how to stack the
wings. This may seem unnecessary, but I like it because during a
short competition (this one was only 2 hours) valuable time can be spent
thinking about how to stack the wings. Having a diagram can hasten
the process. |

Next, I made the templates. Notice the extra pieces on the right &
the temporary support under the tail. Temporary supports add a lot
of strength to the piece while carving. Carefully remove them
towards the end of the competition. |
| |
|
Heron |
|
|
| |
|
1 Block 2 hours |
|
|
|
Time |
|
|
|
|
|
|
|
Cut out Head & flip block |
|
|
|
|
|
|
|
|
|
Break down block |
|
|
|
|
|
|
|
|
|
|
Freeze on tail / angle cut base |
|
|
|
|
|
|
|
|
|
Freeze on wings |
|
|
|
|
|
|
|
|
0.5 |
|
Freeze on head |
|
|
|
|
|
|
|
|
1 |
|
Carve Bird |
|
|
|
|
|
|
|
|
0.25 |
|
Carve base & legs |
|
|
|
|
|
|
|
|
0.25 |
|
Clean |
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
Do you know how to get to Carnegie Hall? Practice, Practice,
Practice
While practicing, jot down times when you reach certain benchmarks.
During the competition refer to you benchmarks. If you are falling
behind consider a slight modification to your design. For instance
if I ran short on time, which I did, I would not carve the spare legs
completely. I just left the ice in a safe place in case I needed
it at the very end. I would much rather have had 2 spare legs
completely carved, but I had to make an adjustment. |
|
|
Tools required |
|
|
|
|
|
|
|
|
|
|
Templates |
Bucket |
|
|
|
Layout jig |
|
brush |
|
|
|
Chainsaw |
|
Tracing bit |
|
|
|
X cord & pigtails |
1/4" die grinder |
|
|
Wing Alum |
Foam |
|
|
|
Iron |
|
12 x 12 alum |
|
|
|
Junichi |
|
Sand paper |
|
|
|
Lg die grinders |
small bubble |
|
|
|
Shaper |
|
vee bit |
|
|
|
Face burr |
|
eye ball maker |
|
|
|
Syringe |
|
marker |
|
|
|
Green sander |
|
|
|
|
Sm chisel |
|
|
|
|
|
Torch |
|
|
|
|
|
|
|
|
|
Do you know how to get to Carnegie Hall? Practice, Practice,
Practice
I practiced the heron twice.
As you practice, jot down all of the tools you used. By doing
this, you will know exactly what tools to pack for that
competition. |

The finished piece. It was very difficult to photograph because of
a large snow bank right behind it. Sarah had to crouch way down to
get this photo. This sculpture earned a gold medal :) |