-
1/2″ 8″ Ballnose End Mill Bit with 1/2″ Inch Shank
$139.98Great for 3D CNC carvings
10,000 RPMs Recommended
Recommended Step over setting is .1″ for 3D Areas -
1/4″ Ball Nose End mill Bit with 1/2″ Inch Shank
$89.98 Read moreGreat for 3D Carvings
-
1/2″ End mill Bit 2 Flute 1/2″ Shank 8″ Inch OAL Duggan Bit
$159.98Recommended Speeds
RPMs – 10000
Feed Rate – 1.5 inch/second
Plunge – 1 inch/second -
Shot Glass Bit 1/2 Inch Shank
$519.98If used in CNC –
1200 RPM
3″ thick Ice
Plunge 2.6″ deep
Z Speed .3″/second (18″/minute) -
Ice Sphere bit 1/2″ Inch Shank
$389.98 Select options This product has multiple variants. The options may be chosen on the product pageCreate Perfect Ice Sphere using a Drill Press or CNC.
1/2″ Shank
-
Square Sphere Table Jig
$229.98Compact Ice Sphere jig allowing you to make up to 4 sphere from a blank
-
Large Sphere Table Jig
$349.98Adjustable table for Ice Sphere making allowing you to make up to 12 spheres from a blank at a time
-
1/2″ End Mill Bit 1/2″ Shank 6″ Inch OAL 2 flute
$72.98For use in an ice lathe
Recommended RPM- 14,000
Recommended feed rate for Spindle- 3″/Second (180″/minute)
Recommended feed rate for Router- 2″/Second (120″/minute) -
1/2″ End Mill Bit 1/2″ Shank 6″ Inch OAL
$99.981/2″ Shank x 1/2″ Width x 6″ Over All Length 3 Flute Endmill with 4″ of cut
Recommended RPM- 14,000
Recommended feed rate for Spindle- 3″/Second (180″/minute)
Recommended feed rate for Router- 2″/Second (120″/minute) -
1/2″ End Mill Bit 1/2″ Shank 6″ Inch OAL Ball Nose
$89.98 Read moreFor use in an ice lathe
Recommended RPM- 14,000
Recommended feed rate for Spindle- 3″/Second (180″/minute)
Recommended feed rate for Router- 2″/Second (120″/minute) -
1/2″ End Mill Bit 1/2″ Shank 8″ Inch OAL
$129.98 Read more3 Flutes, 8″oal, 5″ of cut
Recommended RPM- 14,000
Recommended feed rate for Spindle- 3″/Second (180″/minute) -
1/2″ End Mill Bit 1/2″ Shank 7″ Inch OAL
$126.983 Flutes, 7″oal, 5″ of cut
Recommended RPM- 14,000
Recommended feed rate for Spindle- 3″/Second (180″/minute)
Recommended feed rate for Router- 2″/Second (120″/minute) -
1/4″ End Mill Bit XL 1/2″ Inch Shank
$84.98Recommended RPM- 24,000
5″ overall length1/2″ shank 3.5″ length of cut 1/4″ tip
This bit fits in both the above 1/2″ end mill holder & a CNC collet. -
Medium Die Grinder Shaft
$109.98“Medium Shaft” for the Medium Makita 600’s
-
Large Die Grinder Shaft
$119.98“Large Shaft” for the Large Makita 800 for ice carving
With high quality bearings -
Neck with Shaft for 800 Makita Die Grinder
$219.98Fits large Makita die Grinders
Shaft Installed
Take out 4 screws and swap with this pre-assembled neck -
1/2″ Inch End Mill Bit Holder
$64.98Accepts all bits with 1/2″ shanks
Threads onto either die grinder with a shaft installed -
3/8″ to 1/2″ Inch Sleeve
$29.98
